Evinrude/Johnson Bad Years? - iboats Boating Forums
2007年8月27日 · Re: Evinrude/Johnson Bad Years? it's a word i can't say. yes it was the larger motor. direct injections, all kinds of electronics. the good ole carborated omc motors are as good as any. if it says FICHT, you are better staying away. the shops were not prepared for the technology, and poor support from OMC.
What's the difference, Johnson/Evinrude - Boating Forum
2006年10月21日 · Re: What's the difference, Johnson/Evinrude In the old days, Evinrude was a step up and Johnsons were for the masses. I have 3 1950's Evinrudes. Each one was produced at the Johnson factory in Peterborough. The powerheads are all Johnson red underneth their "original" Evinrude blue paint.
Evinrude E-Tec? Pros/cons - iboats Boating Forums
2007年3月24日 · Re: Evinrude E-Tec? Pros/cons I think that resurrecting a two year old thread can lead to a lot of confusion. I just attended the New England Boat Show in Boston Feb. 18, 2009 and around half of the outboard boats on exhibit were sporting BRP motors, including the twin motors on the Massachusetts Environmental Police boat.
Mid to late 1960's Evinrude Fastwin 18,...are they good motors?
2009年7月11日 · Re: Mid to late 1960's Evinrude Fastwin 18,...are they good motors? the old 18's are great! grab it. It will do well on a boat rated for 25. In fact the old 33 was an 18 with a bigger carb, or so i was told. You don't need electric start on it either so bypass it and save some weight. Keep the 9.9. A guy can't have too many motors.
1981 Evinrude 35hp tiller conversion kit? - Boating Forum
2024年12月15日 · I have been looking at all the different sites with parts breakdowns on Evinrude motors. I have a 35hp electric start,long shaft with remote controls. I would like to change it to tiller controls. It is a model number E35ELCIG, serial number E0004143. Is …
Oil Mixture on old Evinrudes outboards - iboats Boating Forums
2024年4月25日 · OMC motors before 1964 often had sleeve bearings, versus roller bearings. Sleeve bearings need more lubrication, hence the 24::1 recommendation for all OMC motors before 1964. As for the 100::1 gas/oil mix, the drawback was loss of crankcase rust control, with so little oil in the fuel.
E-Tec engine reliability? - iboats Boating Forums
2012年2月14日 · i have had a couple of older evinrude motors..both had serious issues and one i rebuilt and it only lasted a couple of years. i have a suzuki dt-55 that has been good for many years but now has an overheat issue etc..8 months of struggle and now time for a new used motor. so..the hype i have...
Diference between 25 28 and 30 hp Johnson/Evinrude motors
2012年4月19日 · Re: Diference between 25 28 and 30 hp Johnson/Evinrude motors O.K. thanks for the replies... I currently have at my disposal a complete 55 Johnson 25 hp powerhead (good condition) as well as a 62 Gale 25 hp powerhead (pistons and block are good but rods and crank are toast (rusted).
What gearcase lubricant should be used on Johnson and Evinrude …
2011年9月1日 · Hello, I have one Johnson 1962 40hp and one Evinrude 1968 18hp motor and both are manual shift. The manual mentions OMC Type C lubricant for the lower unit's gearcase. However it is hard to find nowadays. I am just wondering if Pennzoil Marine 80W90 Gear Lube found in Wal-Mart can be used...
Which oil to use on an older Evinrude motor - Boating Forum
2011年5月28日 · Re: Which oil to use on an older Evinrude motor The XD-100 synthetic oil would be great for your motor but is not worth the extra cost of the premium oil. XD-50 would be the best all around lubricant as it is semi-synthetic, helps clean the carbon inside the motor, and it hardly smokes at all at 50:1.