2024年9月6日 · If you install a Victron Smart shunt directly on the negative terminal of the battery(set), you can monitor all the current going in and out of the batteries with the Victron app. When you install a Cerbo GX, you need a Ve-Direct cable from the Smart Shunt, and from the Smart MPPT, to the Cerbo GX. And you can connect the Phoenix to the Cerbo ...

2024年7月3日 · This topic covers the SOC / Amps reported by BMV battery monitors, SmartShunts, Lynx BMSs and Lynx Shunts and will just be called shunt below. It is also assumed that the shunt is monitoring the domestic / house / cabin battery bank and not engine start / bow thruster / winch / caravan mover battery banks. The problems may be one or more of the …

2024年11月5日 · Camper with two Volthium lithium batteries, Victron battery monitor and solar controller. Below is a screenshot of the Victron app. Notice it shows 13.11V on the batteries and a 96% charge. The chart I have been using shows 13.1V with a capacity of 40%.

2024年7月4日 · For example, with 500Ah of battery, the battery monitor could be set to 2% tail current, which is 10A. The solar controller can then be set to end absorption at say 8A. Note, if you have for example, the Victron Lithium Smart (or NG) batteries where absorption ends after a fixed 2 hours rather than by tail current, this point does not apply, it ...

2024年9月23日 · I have a bank of two 12 v batteries connected in parallel. Apart from the two connector cables between the batteries, there are connections to loads or chargers on each the 2 positive and 2 negative battery terminals. Judging by the different cable diameters, these connections are in pairs and diagonal across the battery bank, so all OK. Now, to install the …

2019年12月11日 · Our 4 cell 300Ah LiFePO4 battery has started our 3.9l turbo diesel motorhome engine perhaps one or two thousand times over the last 8 years of fullime travel. Peak starting current current reaches 740A but only for fractions of a second. The Victron 500A SmartShunt and 400A Junctek battery monitor shunt in series still look brand new.

2024年11月5日 · Hello, I’m installing a Victron 712 battery monitor with shunt and Orion TR smart DC to DC non isolated charger together in a campervan. I understand that with the non isolated dc to dc charger the start battery and the house battery must share a common (chassis) ground. In the installation instructions for the 712 there is no indication that the negative side of the …

2024年10月9日 · Hello folks. I need help here. I have two MP2 setup as split phase. Also have a cerbo gx, 4 smartshunts of which 3 set up as DC meters and connected to my Solar charge controllers (non-Victron), 1 set up as battery monitor between some loads and battery bank. I always have to manually set the battery monitor to 100% SOC charge. Problem is that the …

2024年9月30日 · I have a BMV-712 Smart Victron battery monitor, and 2 mppt 75/15 regulators. 1 monitors my campers rooftop solar panels, the other monitors my external solar blanket. Battery monitor shows 13.33v and SOC 82%. Sun is out → the rooftop solar regulator is showing battery voltage of 14.4v (! NOT matching the battery monitor) and hence charge state = …

2024年9月13日 · I have a 45kva three phase battery pack. The pack contains 12x200AH Victron smart lithium batteries in a 3x4 series-parallel 48v configuration with the associated Victron lithium BMS hardware. These batteries are connected to 3xQuattro 15kw inverters setup in a three-phase configuration. The battery currently has a colour control GX to monitor the inverters and the …