2024年10月29日 · I’m having an ongoing issue with my Smart Solar Charge Controller MPPT 100 | 50 I’ve had all-in-one inverter units before that had direct input from the solar, so I’m new to this. The charge controller doesn’t put enough power into my batteries to charge them. And if it does charge them to 24, if I turn anything on in my house it just drains them out and the controller …

2024年9月17日 · My Smart Solar 100 50 worked perfectly the first day. Then I turned it off and disconnected my whole system to leave the house for two days. Plugged everything back in and now my controller is staying on float even though my inverter is reading 22.9 for my batteries. Could the problem be that the controller is currently set to 12V? I believe the batteries are 12V …

I will use 6AWG from the panels to the Victron 100/50 smart solar controller which will be within 3' of the batteries. 6AWG is good for 37amps effective use current, so that should be more than enough for the approx 20' fun from the panels to the controller (i'm open to other suggestions on wire size if you have advice).

2024年9月25日 · Please Help. I have a MPPT 100/30 Smart Solar charge controller. I tested the panel and connected it and it worked fine. I then disconnected it so I could mount it on the vehicle roof. After mounting it and reconnecting the panel to the charge controller, it only shows low voltage varying between 2-13v no higher I have tested all the wiring and connections the …

2024年9月5日 · I just bought a SmartSolar MPPT 150/35 to run six solar panels. I also have a wind generator. I idid have a non-branded Chinese hybrid controller but its internal limits would not allow me to generate more power when I went from 4 to 6 panels, so I took it offline. I had a Renogy Rover 30, and I ran it and the wind controller wiring to the same battery bank. …

2024年9月7日 · Hi, I am quite new to all this. I bought the above charger and had it on a solar panel of 15 watts charging 2 100Ah AGM batteries that are for running a diesel heater in the winter. The batteries sat at 12.2 volts all of the time. I bought a 420 watt solar panel and plugged that in instead, now the batteries charge and seem to be happy at around 13.7 volts. I …

2024年9月27日 · Hi, I would like to know if the battery negative and the load output are common on this model? They appear to be. The reason I ask is I am running a 3 core cable to another spot and would like to use all cores such that the one of the cores will be negative and the others will be permanent battery +12v and a load +12v output which is set on the streetlight function? …

2021年11月16日 · 3. Victron Smart Shunt 500A/50mv 4. Victron 100/50 Solar Charge Controller 5. Victron GX Display and finally 6. Victron Multi "Remote" Control 200/200A GX. The final piece that put me over the edge was the Remote Control unit for the Inverter.

2023年11月1日 · I have an Blue Smart IP22 Charger12v/30a 3 battery version. I have 2 seperated systems (only sharing common ground) 200A(2x100 paralel) and 160A (2x80 paralel) AGM battery's. I combined the 4mm2 ground cables in the charger to …

2024年10月28日 · I’ve been working with a VE.Smart network of 3 SmartSolar MPPTs (100|30, 100|50, & 150|70) and a BMV-712, and I recently got a Cerbo GX MK2 to preempt some system upgrades while also building a custom dashboard. I have all 4 of those devices wired up with VE.Direct cables to the Cerbo, and they all show up via the Cerbo’s remote panel. I wanted to …